• Sourcing Solutions
  • Services & Membership
  • Help & Community

IP Camera: a IP Camera who not only capture video like common CCTV Camera, but also compress data and send data to end-user via LAN, Internet or WLAN. You can publish and view video only need to plug network cable or set wifi signal and power ip camera. IP Camera has its own microprocessor, often use linux operation system, built-in web server, support multiple network protocols. IP camera has its own ip address and DDNS domain name, it can be viewed by inputting ip address into IE browser address bar or via CMS software. It is widely used for office, building, chain enterprise, large factory machine room, remote elder children nurse, public buildings, nobody dangerous environment monitor, finance institution branch monitor, traffic monitor and etc.


Rearview Camera: a closed circuit television CCTV camera with mirror image used on car / bus / truck while reversing. It adopts wide angle lens to form wide angle view. The size is mini. It is waterproof camera and water resistant level is IP66, so you can feel free to install it at rear side of the car. It can be worked with car DVR recorder, quad processor. It can be viewed through LCD monitor, TV and etc.


HD: high definition, 1080P(1920*1080); 720P(1280*720)


WIFI: Wireless Fidelity, wireless local area network, WLAN. Wireless local area network based on IEEE 802.11b/g/n, a local area network that uses high frequency radio signals to transmit and receive data over distances of a few hundred feet; uses ethernet protocol.


P2P: PNP, plug-and-play, a progress of interface technique, plug and play, no need people operate.

1. Power Camera:

Input SIM card into 3G IP Camera’s card slot, Connect power supply (DC5V2A), when the power LED is on, the device starts.


2. Plug Cat5 Cable:

Plug one end of network cable into ip camera, plug the other end of network cable into router or switch, then network LED is on, showing connection well.


3. Set IP Address of IP Camera:

Factory default setting in network parameters of the camera:


Subnet mask:


HTTP port: 80

RTSP port: 554

Network camera must be in the same network segment with PC. First of all, the gateway and subnet mask should be the same. Secondly, IP address is also in the same paragraph, such as:

IP address of PC is

IP address of the camera must be in the range(except

If their network parameter is inconsistent, you need to update the network parameter of the camera.

Run the Search tool to search cameras (search tool that comes with the product CD)

Click Update IP, change camera network settings, then search again, the camera will display the updated IP address.


4. Access via IE browser:

Input IP address of network camera, such as: HTTP port is not 80, need to follow with HTTP port. Input user name and password. After login in, if the view page is blank, please install OCX control in CD or operate as following steps:

a. open an IE, click tool-internet option-security-customize level-enable all the ActiveX control-security level low-confirm

b. close firewall

c. close anti-virus software


5. View via CMS:

Install software in CD and View via software for multiple camera monitor.

Frequently Asked Questions for IP Camera:


Q: Why can I use the search tool to search out IP address of the IP camera, but I cannot use IE and software to access cameras.

A: This may be because of the network and camera’s net segment does not belong to the same segment, must use search tool to update IP address of IP camera to meet same segment of local network.


Q: Can I access camera via another browser other than IE?

A: no, our OCX controls inside the camera is based on IE browser kernel, apply only in the browser based on IE core.


Q: Why the camera can be accessed by IE or connected to the software, but cannot see the image.

Answer: first of all, make sure to use the correct browser access to the camera, and you successfully install and load the OCX controls; secondly, ensuring smooth and sufficient network bandwidth, you can use the PIN command to view network latency or switch.

Enter the “pin (IP address of the camera) – t” see network

If the delay is greater than 300ms or there is a long time "no response", it can be difficult to get the camera of high resolution images, so there may be no image, then you can try to change the camera resolution settings, limit the number of bit-rate frames or bit rate, or changed to a lower resolution.

If the above settings or network is normal, but still cannot see the image, it may be a problem with the camera itself, contact the vendor for assistance!


Q: I can not search out IP address of the IP camera via search tool.

A: the camera could not be found due to a lot of camera hardware, software, network environment, and so forth will result in camera is not found:

Search tools: search tool searches camera within the LAN network by sending broadcast packets, when you run the network connection between the PC and a webcam software gateway (routers, for example), the gateway to filter broadcast packets, the search tool will not be able to search into the camera.

PC: PC does not turn off the firewall, or other security software blocking. Through DHCP assigned IP address of the PC, but the allocation of IP addresses is not valid.

In the PC and the camera does not belong to a local area network.

Network: ageing switch entry needs to restart.

Router IP address filtering or blocking, and so on.

Or cable aging network Crystal head oxidation causes, such as lack of network access.

Camera: camera long because some of the causes of internal service is not running or has stopped running, needs power failure restart camera.

Camera does not power on, or power supply problems, camera using POE power supply but POE module is damaged.

Camera has been damaged.

Because there are many possible reasons, IP address may not be found. If the camera appears unable to access, can not search out IP address via search tool, we propose to check in this order:

1. Using a normal access to other cameras or sound preparations for the PC directly connected cameras.

2. Manually specify the IP address of the PC and the camera is in the same network segment.

3. Use a good network cable to directly connect the camera and PC.

4. Check camera power connections, and make sure that the camera is powered on.

5. Use the search tool to search the camera or use IE directly access attempts to connect to the camera. If you follow the above steps and still unable to connect the camera, it could just be a problem with the camera itself, contact the vendor for assistance!

 contact with Aimee  Sally



 contact with EvaBecky



  contact with EvaEcho



  contact with EvaBosh



  contact with EvaJoson



  Contact with Eva contact with EvaEva 



  Contact with Mark  contact with EvaMark

Trade Assurance
China (Mainland)
Transaction Level:
Supplier Assessments:
26 Transactions 10,000+
The supplier’s transactions conducted via Alibaba.com in the past 6 months.
The supplier supports Trade Assurance – A free service that protects your orders from payment to delivery.
Supplier's Trade Assurance Limit: US $81,000
Learn More


Email to this supplier